An iron is an important inclusion to any laundry and will help you keep your clothes in a presentable condition. There are also irons that can be adjusted to suit different types of clothing materials, such as a steam iron or steamer iron which will help your clothes hang better without damaging the material. Browse our iron range to find the ones that are suitable for your clothing types. We also have garment steamers, which are good for those clothes that can't be ironed, so that you can look neat and tidy in your fancier clothes. Our garment steamers also come with their own hanging system for easier steaming. Make sure to check out the full range of our iron and garment steamer products, as they come with a range of features designed to make it easier for you to prepare your clothes. For more help finding the suitable iron or garment steamer for you simply contact one of our friendly sales associates through our website, over the phone, or by going in store today! As a very general rule, one should replace the fluid in their brakes at least once per year, even if you don't notice any degradation in performance.

If you ride more than average, or spend a lot of your saddle time in a bike park banging out laps on the char lift, you may want to do a bleed more often. A quick check of the fluid by leveling the lever so it's parallel to the ground and removing the reservoir cap will allow you to see if the mineral oil in the system is cloudy or dark with contamination. Keep in mind that some mineral oil is darker than others, but if it looks hazy or you spot any floating bits, it is time to perform a bleed. Likewise, a spongy feel at the lever, excessive lever pull, or brakes that pump up (meaning the bite point changes when they get hot during use) all mean that it is time to do this job.• As always, a clean work area can make this job go smoother. Take a minute to clean up your bench and put away the tools that you won't be using.• Always remove your pads and put them somewhere that they won't get fluid on them when you make a mistake and get drenched. It will happen at some point. Likewise, put your wheels in a safe spot as well...

Not leaning up on the repair stand under your bike!• Remember that you may have to overfill your Shimano system while bleeding which could make a bit of a mess. oreck little hero canister vacuum cleaner reviewsWhile mineral oil isn't going to cause damage like DOT fluid can, you may still want to put an old towel on the floor, under your bike. euroclean wet and dry vacuum cleaner demo video• While some Shimano brakes incorporate a small phillips screw that you can use to adjust the bite point of the brake, its range is very limited and has little effect. vacuum cleaner sharp ec 8304If you're looking for less lever pull than what the screw allows, now is the time to make that adjustment.

With the bleed nipple on the caliper closed, gently pull the lever to pump the pistons out ever so slightly. Remember that having the pistons protrude only an extra millimeter can have a huge effect on the lever pull. You can test the results by reinstalling your pads, after being sure to clean any mineral oil that may have been present on the caliper, and giving the lever a squeeze once you've place a rotor between them. If you've gone too far you may get some pad rub on the rotor. Reset the pistons using a plastic tire lever and try again. Most importantly, never use anything other than mineral oil in your Shimano stoppers, and I highly recommend using Shimano branded oil. Many other brake systems use DOT brake fluid, the same as your car uses, but the two fluids have very different properties and are not interchangeable. The rubber seals in your Shimano brakes will be quickly eaten away by the much more corrosive DOT fluid, rendering your brakes useless in no time. A quick stroll through your local pharmacy or auto store will show you that there are a number of different mineral oils available, but the majority of those will not work for this job.

Many of those oils will be far too thick to work well, or have perfumes and other chemicals that will damage your brake system. Anything mineral oil from a pharmacy will not only be too thick, but is intended to be used as a laxative. Use that stuff when you need to pooh, not stop your bike. Likewise, a quick search of the forums and you'll see people exclaiming how they've used fork oil or automatic transmission fluid... there is a good chance that both of those options are too thick and will make your brakes feel sluggish, not to mention possibly having additional chemicals in them that could damage the seals in your brakes. What should you use? Despite it costing quite a bit more than some alternatives that may or may not work, I always recommend using Shimano branded mineral oil. I'm sure many readers will pipe up with options that they've used in the comment section below, but by using Shimano mineral oil you'll know that you won't have any problems. Yeah, it costs quite a bit, suck it up and buy the right stuff though and you'll know that you won't have any issues.

What's needed: 3 mm hex key, small phillips screwdriver, a 7 mm wrench, clean rag, isopropyl alcohol, the yellow Shimano bleed block, some tubing and a bottle or small plastic bag, and of course some Shimano mineral oil. Looking for a bit of help? Check out the technical documents on Shimano's website for more information.:Technical Tuesday #1 - How to change a tube. Technical Tuesday #2 - How to set up your SRAM rear derailleur Technical Tuesday #3 - How to remove and install pedals Technical Tuesday #4 - How To Bleed Your Avid Elixir Brakes Technical Tuesday #5 - How To Check And Adjust Your Headset Technical Tuesday #6 - How To Fix A Broken Chain Technical Tuesday #7 - Tubeless Conversion Technical Tuesday #8 - Chain Wear Technical Tuesday #9 - SRAM Shift Cable Replacement Technical Tuesday #10 - Removing And Installing a HeadsetTechnical Tuesday #11 - Chain Lube ExplainedTechnical Tuesday # to see their entire lineup of tools and lubes. Strive vs. Strive: EWS Bike Setup With Justin Leov and Joe Barnes